Numbers on measuring tape

Posted on Posted by Merisar

This has made me feel confident in doing the tasks at home that I have avoided for years.

Numbers on measuring tape geberit back to wall cistern

First, mark the spot where the measuring tape lines up with the edge of the thing you're measuring. Find the nearest inch before this point. Then, find the nearest half-inch before this point. Then, the nearest quarter-inch, and so on. Add up your inches and fractions of inches until you have an accurate measurement. This is a lot easier than it sounds — see below for an example.

Let's say that we've measured past the one-inch mark, past one quarter-inch mark, and past one eighth-inch mark. If you need help, see our article on how to add fractions with unlike denominators. Use the big, numbered markings for centimetres. On most metric measuring tapes, centimetres are the most prominent markings. Centimetres are usually labeled with large lines and, next to each line, a number.

As with inches, the line marks each centimetre, not the number itself. After each metre, the centimetre markings may start over again from zero or continue counting. This varies from measuring tape to measuring tape. Use the smaller markings between centimetres for 0.

Some but not all metric measuring tapes will have medium-sized marks evenly spaced between each centimetre mark. These mark half-centimetres. These marks are usually not labelled with a number. For this reason, it's usually fine to refer to half-centimetre markings in decimal terms i. Use the small, densely-packed markings for millimetres.

The small, tight, narrow lines between centimetre markings represent millimetres or one-tenth-centimetres. There are ten millimetres in a centimetre and, thus, one thousand in a metre. If your measuring tape doesn't have 0. Add the centimetre segments to determine the total length. To measure with a metric measuring tape, first find the nearest centimetre before the distance you're measuring, then the nearest millimetre.

You can use a 0. Your measurement in centimetres will be a decimal where the tenths place is indicated by the millimetre marking. For example, see below: [6] X Research source Let's say that we measure past the 33 centimetre mark to the sixth millimetre marking.

For example, let's say that we want the answer above in metres. In this case, since there are centimetres in one metre, we could use a conversion factor like this: Method 2 of Retractable Tape. Catch the hooked end on one side of the object you're measuring. If you're using a retractable tape measure the kind that comes in a small metal or plastic box that automatically sucks the tape back up when you're done with it note that the end of the tape will almost always have a small metal notch at the zero mark.

This is useful for holding the tape in the right place as you measure, so you may want to start by catching it on the edge of the object you're measuring. On the other hand, if you're measuring something that can't be latched on to like, for instance, the distance across a door frame , just press this metal notch into one side of the object.

Stretch the tape across your object. With the zero mark in place, pull back on the box to let more tape out. You can use one hand or a friend to hold the end of the tape in place as you pull it back. Let tape out until it stretches all the way across the distance you're measuring. Try to keep the tape straight as you do this — if you let it sag which is easy to do if you're measuring long distances , the results you get will be skewed.

Take a reading directly from the tape. Now, look at the point where the tape meets the end of the thing you're measuring. The nearest number below the end of the tape is your number of units you're measuring and the markings between this number and the one above it correspond to fractions of the unit. For example, if you are measuring across the front of your dresser and the edge of the dresser lines up right after the 24 inch marking, this means that your dresser is between 24 and 25 inches wide.

You can also try putting a kink in the tape, then lining up this kink with the edge of what you're measuring. This is handy in certain situations, like for instance, when you're measuring into a tight corner. Use the lock switch to keep the tape at the same length. Most retractable tape measures will have a button or sliding switch that, when pressed, keeps the tape measure from being sucked back in. Some even lock automatically. For instance, the lock feature is useful for: Quickly seeing which of two objects is bigger Seeing whether something will fit through a certain space Keeping the tape available for multiple quick measurements Keeping a certain distance "handy" to avoid having to re-measure.

Hold one end of the tape down at the start of your distance. A manual tape measure which looks a little like a long, skinny ribbon or a ruler made out of flexible material lacks some of the convenient features of a modern retractable tape measure, but with the proper technique, it works just as well. To start taking a measurement, grab the "zero" end and line it up with the start of the object or length you want to measure.

Part of the problem with manual tape measures is that they're most useful for measuring only short differences because you have to be able to hold the zero end in place while you move the other end into position. Thus, most manual tapes won't be much longer than the human arm span. If you need to measure beyond your reach, you can try keeping the zero end of your tape measure in place with a weight or getting a friend to help.

Stretch the tape across your distance. Now, take the slack of the object and lay it in a straight line across the object or distance you want to measure. Be sure to keep the tape tight to ensure an accurate measurement, but don't stretch it — most modern measuring tapes are made out of semi-flexible plastic.

Just as you would with a retractable tape measure, look for the spot where the end of the object or distance you're measuring lines up with the tape measure. The distance indicated on the tape measure at this point is the distance you've measured. For instance, let's say you hold one end of a tape measure in the tips of your fingers and stretch the other end all the way to the crook of your armpit to determine how long your arm is.

If the tape measure stretches exactly halfway between the 27 and 28 inch markings, this means that your arm is If measuring around a round object, pinch the tape where it overlaps. One advantage of ribbon-style tape measures over retractable tape measures is that their flexibility allows them to measure around objects. To do this, place the zero end of the tape on the object, wrap the tape all the way around it in as straight of line as possible, and note the point where the tape measure first passes the zero marking once again.

This point is the distance around your object. For example, if you want to find the distance around your wrist, place the zero end of the tape measure on top of your wrist, wrap the slack around and underneath, then line it up with the zero end on top.

If it is, for instance, six inches at this point, then your wrist has a circumference of about six inches. Why is there an arrow marking on 16, 32, 48, etc. This a common layout measurement for various items used in building homes and other structures. Get hassle-free estimates from local trim carpentry professionals and find out how much your project will cost.

Get Free Estimates. Learn how to read a ruler with descriptions on what all of the markings mean. Standard rulers and metric rulers are illustrated. To find linear footage, simply find the measurement in feet. Calculate square yards by entering length and width measurements.

Estimate material costs and yardage for carpet and flooring projects. You are here. In order to read a tape measure you need to understand what all of the little markings mean. The ticks between the inch markings and half-inch markings are quarter-inch markings. The smallest ticks on a tape measre are sixteenth-inch markings. Unfortunately, the movement on the hook isn't accurate on all tapes, and it can lose accuracy over time. If you really need an accurate measurement and you believe that the hook is not moving properly, you can do a simple technique called "burning an inch.

This eliminates any inaccuracy from the hook. You just have to remember to subtract that inch. Tape measures usually have a red mark every 16 inches. Unless you are dealing with wall studs or joists, you can ignore this marker. Tape measures can be more hazardous to the operator than they may seem at first.

Instead, reel it back slowly. The whole inch, or 1-inch, mark on a tape measure is the longest and easiest to see. Foot markers are the longest lines on the tape measure and sometimes extend the entire width of the tape. Most tape measures tell you where each foot mark is located, along with the whole inch designation. The whole inch mark is the easiest to read on the tape measure because the number is clearly stated on the tape. There is no guesswork.

Top view of numbers on measure the height of a. What would you use to. What instrument is used to measure from the school fence. Who is the longest reigning a tape measure. Can you give the phone WWE Champion of all time. What is the function of a jar on white background. What is tape measure used. How do you measure a. What is rounded to the. Beautiful young business woman smiling shocked after looking at the.

How to read a tape measure easy and figure fractions on a measuring tape U.S. Tape Co. offers a variety of tape measures, including models with inch, fractional and metric designations. Learn how to read each of them in our blog.  Depending on the tape measure, these may not be designated with a number, which means you’ll need the markings on either side to guide you. In other words, the half-inch mark between inches 13 and 14 is read as 13 ½ inches, and sits exactly midway between the markings for those numbers. 3. Quarter inches, eighth inches, and sixteenth inches. Most standard tape measures in the U.S. have markings that measure down to 1/16 of an inch. These are smaller, sometimes thinner markings, evenly spaced between the half-inch and inch marks on a tape measure. How To Read Measuring tape|What Are The Numbers On Measuring Tape Hello, Welcome to our you tube channel Mechanical Dhruv. About this Video- In this video I. While every person knows how to use a measuring tape, almost none of us have any idea of the small markings and numerals that are subtly placed in between the numbers and dashes. Today, we are going to give a full low down on all the nitty-gritty of a measuring tape so that you work as a professional next time. Pic Credits: Diply. We start off with the obvious details: the larger numbers at the top represent inches, while the smaller numbers on the bottom of the tape indicate centimeters. Credits: the tape store. These circled Roman numerals are sometimes present in between and represent the l.

936 937 938 939 940

Так же читайте:

  • Shower diverter valve not working
  • Makita 2470 sds drill
  • Non steel toe work boots
  • Knives case
  • walkie rider pallet trucks

    One thought on Numbers on measuring tape

    Leave a Reply

    Ваш e-mail не будет опубликован. Обязательные поля помечены *

    You may use these HTML tags and attributes:

    <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>